split pressurized solar water heater for morden house - JSH1-150-18

Split pressurized Solar water heater for morden house.

This high efficiency vacuum tube split pressurized solar water heater contains almost everything needed for a solar hot water heating system. It can be easily integrated with your house, the solar collectors can be installed on general different type of roofs, and tank can be placed anywhere as you like.

The JINYI Solar JHC Range of vacuum tube heat pipe solar collectors offer excellent value as they have both a very low cost per kWh of output and a high efficiency. The collectors are also very easy to transport and handle as the tubes can be disconnected from the manifold of the collector.

The split pressurized solar water heater contains:

Solar thermal collector (evacuated tube or flat plate) which absorbs solar radiation (sunlight) and changes it into heat;

Circulating pump which transfers the heat from the collector to hot water in a storage tank;

Solar hot water tank accumulates the hot water produced by solar energy so that it can be stored for use when needed;

Accessories which ensure the regulation and the safety of the system;

Back-up heater (gas, oil, or wood fuelled boiler, immersion heater or heat pump) which will bring the hot water to the temperature required when there is not enough sunlight to do so (mostly in winter).

In most area, solar collectors alone cannot provide all the hot water for a household’s needs throughout the year. Correctly sized they will supply 60% of heat / domestic hot water needs. They are normally installed in conjunction with a conventional back-up heating system.

Solar thermal collector evacuated tubes collect and convert sunshine energy into thermal energy, which is transferred to the central heat pipes in the tubes through the aluminum fins bridging the tube inner surfaces and the heat pipes. The copper heat pipes have tiny amount of purified water sealed in them at depressurized condition. When heated, the water inside the heat pipes vaporizes at low temperature (about 30 deg. C). The vapor (steam) rises to the pipe tips inserted into the water contained in the tank. Vapor is cooled down and becomes condensate falling to the bottom of the pipes. By continuously circulating this way, heat is carried from outside to the water inside the tank.

Components:

1 x JHC-5818-18 heat pipe solar collector 2.30m² (1.687m² aperture)

• 4 x Roof hooks (JRH1)
• 1 x Air vent valve (JAVV)
• 1 x Female equal tee 1/2" (JFET)
• 2 x Straight adaptor 3/4"-1/2"(JCFSMA)
• 1 x Equal male straight 1/2"(JES)
• 1 x 150 litre one coil 304 stainless steel tank including insulation
• 1 x Exchanger of copper coil inside of tank, dia. 12 x 1.0mm, 15m
• 1 x Electric heater 1500W (JEH2)
• 1 x Magnesium rod (JMR2)
• 1 x T/P valve (JTP)
• 1 x Relief check valve (JRCV)
• 1 x JPS1 solar pump station
• 1 x 5 litre expansion vessel (JEV-5) with connectors
• 1 x Safety valve (JPSV)
• 1 x "Wilo" circulating pump (RS15/6)
• 1 x Controller (SR868C8Q) with two sensors for tank and one sensor for collector
• 1 x Manometer
• 1 x Flow meter

Packing dimension:

• Tank with its accessories (0.477m³): 1550 x 550 x 550mm (1carton)
• Pump station with its accessories (0.035m³): 520 x 340 x 200mm (1carton)
• Vacuum tubes with heat pipe (0.214m³): 1940 x 220 x 250mm (2cartons)
• Collector manifold with frame(0.060m³): 2000 x 150 x 200mm (1carton)

Total 6cartons, 0.782m³