China Yiwu mini air condition hand-held

China Yiwu mini air condition hand-held
1.outdoor air condition
2.protable air condition
3.YIwu air condition office gift

1: there are two kinds of air conditioning works Refrigeration and ordinary fan pattern
The random elealeh, respectively, wet sponge sufficient to don't drop (standard) in the special zones behind sponge machine. Open air conditioning, nov.11 refrigeration can be realized
If don't need refrigeration, criterion sponge remove, continue to open air conditioning, it won't have a cold wind blown out
The wood products with OARS bibulous sponges can reuse!

2: power-supply modes
Air conditioning power-supply modes have 3 kinds
1, 4, section 5 batteries (need the mixed)
2, USB power supply (random matchs a USB line a)
3, power supply (AC adapter directly to users self-provided)

Three, the matters needing attention
A: the product is not waterproof product should be removed, sponge water then adding water. Do not directly, prevent water into water damage machines internal
B: sponge humidity to fill it up dripping shall prevail. If after soaking overmuch can twist dry add machines inside
C: products do not fight high altitude fall, when using, please note
D: Suggestions after each use sponge sponge, lest dry after please bacteria and produce peculiar smell.

Tip: if you need to blow it out with fragrance, you can wind oils in dropping a few drops to sponge on OK. Of course, use after must remember into soak dry clean again.

Battery installation
Battery case is located in the handle, the side with hand
1) downward slide and remove battery case lid
2) installed the 4th quarter new AA alkaline batteries
3) to cover the battery case lid
4) long-term when not in use please take it out
Can the power converter, external power supply device in the DC plug the hand to take on outlet
1) will we can replace the power supply device configuration of the DC plug into the socket mouth
2) grafted in household power can use without battery state with cold

Water-cooling sponge installation
1) took the machine off
2) through the push pull, outside the top leverage the sponge along with water-cooled sponge lid took together
3) the first use of: soak in tap water cooled sponge with soap thoroughly rub. Please be careful, don't wash sponge when too hard.
4) if the sea and the last used the moisture, please leave the sponge removed from the lid, the remaining water firm.
5) please put water-cooled sponge sponge lid flat and press the following describes operation: in the bottle filled with water, distilled water or mineral water, then the uniform slow 30ML poured water into the sponge surface everywhere.
6) to insert point of the faucet, along with sponge sponge lid, then reinstall the lid on the direction to host its locked.

Note: do not excessive soak water-cooled sponge. Don't flow under the tap water pour sponge. Good mastery of the water with 30ML soaking is difficult, please always use the bottle with water.

Note: the machine is not waterproof, please avoid external other water contact.

Note: if in the operation appear slack, so might be your on the water in sponge into excess (see step 5); Or maybe you soak the sponge in before the rest of the water without extrusion previously.

operation
Host battery case protrude above two switch:
1) snowflakes switch can control machine power and air cooler air speed
2) lighting switch can control LED light and shade (top machine for night travel temporary lighting devices)
3) open machines, click the snowflake switch, motor low-speed operation. Click on the run, motor speed can press tell where (environmental regulation)
4) rotating air pipe adjustable air output direction, facilitate bring you better cooling effect
5) when cold air when soaking afresh please reduce sponge sponge [see water-cooling installation instructions ]. Open the sponge sponge sponge is confirmed touch lid and dry. By using the time that USES the different and the different environmental and differences (about half an hour to 3 hours)
6) regularly touch sponge sure it is still wet, if sponge dry, please to soak the sponge

Note: to make effectively cold air produce, sponge must is wet, if not, please follow the installation of cooled sponge instructions.
Maintenance water-cooled sponge
After each operation, by illustration removed the lid, extrusion sponge sponge sponge in the excess water, in air air.

In order to achieve the best effect, please regular cleaning your water-cooled sponge, before use antimicrobial soaked.

Note: please ensure handling sponge hands clean

aroma
In order to have a slight fragrance, you can use your own on the sea water cooling fragrant oil. After the sponge soaking wet sponge [ see water-cooling installation instructions ], on the surface in a sponge dropping a few drops of essential oil, in use need after wash thoroughly.
Don't the same block sponge mixture different smells